How to Properly Size a Diesel Generator for Essential Equipment
Understanding Why Sizing Matters
Choosing a diesel generator that matches your essential equipment sounds straightforward, but small mistakes in sizing can lead to big problems. An undersized generator may struggle to start motors or trip its breaker under load. An oversized one wastes fuel, runs inefficiently, and can shorten engine life through light loading. The goal is to find the rated output that covers both the running demands and the starting surges of everything you need to keep powered.
The process involves identifying your critical loads, measuring their electrical characteristics, and then applying a few practical rules about motor starting current and load banks. No matter what specific equipment you plan to run, the same logical steps apply. This article walks through those steps so you can arrive at a generator size that works reliably, whether for a construction site, a workshop, or a backup power installation.
Step 1: List All Essential Equipment and Their Power Ratings
Start by writing down every device, machine, or system that must run when the generator is operating. Include not just obvious items like pumps or compressors but also lighting, controls, computers, and charging circuits. For each item, find the nameplate data: voltage, full-load amps (FLA), and power factor if given. Convert everything to kilowatts (kW) or kilovolt-amps (kVA) so you can compare them on the same scale.
Pay special attention to motors. A motor draws its full-load current when running steadily, but it can pull three to seven times that current during startup. This is the starting current, and it lasts only a second or two, but the generator must supply it without dropping voltage too low. If your essential equipment includes a large motor, that starting surge often determines the minimum generator size, not the running load.
What to Watch: Induction Motors and Power Factor
Induction motors - found in compressors, pumps, conveyors, and fans - have a low power factor during startup. That means they demand more apparent power (kVA) than real power (kW) from the generator. A generator's rated output is usually given in both kW and kVA. The kVA rating is the one that matters for motor starting. If you only look at kW, you may end up with a generator that can sustain the running load but cannot handle the inrush. Always check the generator's kVA capability against the combined starting kVA of your largest motor or group of motors that could start together.

Step 2: Calculate the Total Running Load
Add up the running kW of all equipment that will be on at the same time. Be realistic about simultaneous operation. For example, a workshop might have a compressor that cycles on and off, a few bench tools, and lighting. The base load is everything that stays on continuously plus the average draw of cycling equipment. For devices that run only occasionally, include them only if they could run during a generator outage scenario.
Once you have the total running kW, add a safety margin. A common rule is to size the generator so that the running load falls between 60% and 80% of the generator's rated kW. This avoids light loading (below 30%), which can cause wet stacking in diesel engines, and also avoids running the generator at full rated output for long periods, which reduces service life. For a typical industrial setup, a 20% to 30% margin above the calculated running load is a good starting point.
Step 3: Evaluate the Starting Load
This step often catches people off guard. A motor's starting current can be several times its running current, and the generator must deliver that surge without its voltage dipping more than about 10% to 15%. If the voltage sags too much, the motor may not start, or other equipment on the same generator may drop out.
To assess starting load, identify your largest motor and any motors that could start at the same time. Add their starting kVA to the running kVA of everything else that is operating. Compare that total to the generator's surge capacity. Most generator specifications list a maximum starting kVA or a percentage of overload capability for a short duration. A generator that can handle a 30% overload for 10 seconds, for example, can usually start a motor that draws 2.5 to 3 times its running kVA, depending on the generator's design.
What to Watch: Multiple Motors Starting Together
If your essential equipment includes two or more large motors that could start within the same few seconds, their combined starting kVA can be huge. In such cases, consider staggering the starts with a time-delay relay or a programmable controller. This lets the generator recover between starts and can allow you to choose a smaller, more economical generator than if you sized for simultaneous starting.
Step 4: Account for Fuel Consumption and Runtime
Once you have a target generator size, think about how long you need it to run. Diesel generators are efficient at moderate to high loads, but their fuel consumption per kilowatt-hour is higher at very light loads. If your essential equipment only draws 20% of the generator's capacity, you will burn more fuel per useful kilowatt than if you ran a smaller generator at 70% load. This is where the trade-off between size and operating cost becomes clear.
For installations that run for many hours or days, such as backup power for a remote facility or a construction site, fuel consumption directly affects your budget. A generator that is too large will also require more frequent oil changes and maintenance because of the extended time spent at partial load. Matching the generator size to the actual load profile saves not just fuel but also wear on the engine.
If your site has a mix of heavy and light loads, consider a load bank. A load bank is a device that adds an artificial electrical load to the generator, forcing it to run at a higher percentage of its capacity. This is useful during maintenance periods to burn off carbon deposits, but it is not a solution for day-to-day oversizing. The better approach is to size the generator as closely as possible to your real needs.

Step 5: Plan the Power Distribution Setup
After selecting the generator, you need to get that power to your equipment safely. This is where power distribution equipment comes into play. A transfer switch is essential if the generator serves as a backup to utility power. It automatically switches the load between the utility and the generator, and it ensures that the generator never backfeeds into the grid, which is dangerous and illegal.
For mobile or temporary installations, you may need a distribution panel or a set of receptacles rated for the generator's output. Cables, connectors, and circuit breakers must match the voltage and current of the generator. Undersized cables cause voltage drop, which reduces motor starting ability and wastes power as heat. Oversized breakers can fail to trip during a fault, creating a fire hazard.
A good practice is to draw a one-line diagram of your power distribution from the generator to every essential load. Mark the wire sizes, breaker ratings, and distances. This helps you catch mismatches before you buy cable or install equipment. If the run from the generator to the main load is long, factor in voltage drop and consider stepping up to a higher voltage or thicker wire.
Step 6: Verify with a Load Bank Test
Before putting the generator into regular service, test it under load. A load bank test applies a known electrical load to the generator and measures its response. This confirms that the generator can deliver its rated output, that the voltage and frequency stay within limits, and that the cooling and exhaust systems work properly under full load.
You do not need to own a load bank; rental units are common, and many service companies offer load bank testing as part of commissioning. The test should simulate both the running load and the starting surge of your largest motor. If the generator passes, you have confidence that it will perform when needed. If it fails, you have caught the problem before a real outage.
When you are ready to source a generator or related power distribution equipment, a resource like epowerhousellc.com can help you compare options from multiple manufacturers. Their marketplace lists new and used equipment, which gives you flexibility in matching your budget and timeline to the right unit.
Step 7: Plan for Maintenance and Monitoring
Once the generator is installed and tested, the work is not over. Diesel generators need regular maintenance: oil changes, coolant checks, fuel polishing if the generator sits idle for long periods, and battery maintenance for the starting system. A generator that runs only during outages can develop problems from lack of exercise. Run it under load at least once a month, ideally at 50% load or higher, to keep the engine and alternator in good condition.
Modern generators often include digital controllers that monitor runtime, load, and alarm conditions. Use these to track fuel consumption and to schedule maintenance based on engine hours, not just calendar dates. If your essential equipment includes sensitive electronics, consider adding a voltage regulator or an uninterruptible power supply (UPS) between the generator and those loads. The generator's output may have small voltage fluctuations that sensitive equipment cannot tolerate.

For ongoing support, the same marketplace that helped you choose the generator - epowerhousellc.com - also offers a range of power distribution equipment and accessories. Their inventory includes transfer switches, load banks, cables, and monitoring systems that can complete your installation. Having a single source for the generator and the distribution gear simplifies sourcing and ensures compatibility.
Putting It All Together
Sizing a diesel generator for essential equipment is a step-by-step process that balances running load, starting surge, fuel efficiency, and distribution safety. By listing your equipment, calculating both running and starting demands, choosing a size with a reasonable margin, and testing under load, you avoid the common pitfalls of undersizing or oversizing. Each step builds on the one before it, so taking the time to get the numbers right pays off in reliable operation and lower total cost over the generator's life.
If you are unsure about any calculation, especially for large motors or complex loads, consult a qualified electrical engineer or a generator specialist. The cost of professional advice is small compared to the cost of a generator that does not work when you need it most.